Diesel Place banner

1 - 7 of 7 Posts

·
Registered
Joined
·
3,291 Posts
Discussion Starter #1
Here’s info I already found:
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Hollander Wheel Number, 6300 </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Wheel Size, 17 x 8.5 </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· 8 Lug on 6.5" Bolt Pattern </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Back Spacing, 5-9/16" </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Wheel Offset, +20mm (Positive Offset) </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Hub-Hole Diameter, Aprox 4-5/8" </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Mfg. in USA </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· P/N, 9594459</H4>
<H4 style="MARGIN: auto 0in"> </H4>
<H4 style="MARGIN: auto 0in">Questions:</H4>
<H4 style="MARGIN: auto 0in">1). Are the Alloy Wheels aluminum or painted? </H4>
<H4 style="MARGIN: auto 0in">2). Are they forged or cast? </H4>
<H4 style="MARGIN: auto 0in">3). One piece or two?</H4>
<H4 style="MARGIN: auto 0in">4). What is the load rating per rim?</H4>
<H4 style="MARGIN: auto 0in"> </H4>
<H4 style="MARGIN: auto 0in">I want to up-rate my l
 

·
Registered
Joined
·
125 Posts
Go with the H2 rims and E-rated 17" tires. The rims are painted, and they fit in the wheelwell without any major mods.


I think you'll be pleased with the results.


Just my .02 cents - but you asked...



Edited by: NCMax
 

·
Registered
Joined
·
95 Posts
<H4 style="MARGIN: auto 0in">1). Are the Alloy Wheels aluminum or painted? </H4>
They are painted on the front side - also available in chrome at a much higher price.
<H4 style="MARGIN: auto 0in">2). Are they forged or cast? </H4>
They are cast.
<H4 style="MARGIN: auto 0in">3). One piece or two?</H4>
One piece.
<H4 style="MARGIN: auto 0in">4). What is the load rating per rim?</H4>
The load rating is not stamped or marked on the rims. These rims are not designed far a high GVWR vehicle like the forged PYOs that come on the 2500HD and 3500 trucks, so I doubt that the weight rating is as high as the PYOs. Note that GM will not even sell a SRW 3500 with PYOs - steel only. I would not use the H2 wheels on a truck that I intended to load up to or beyond the RAWR.
 

·
Registered
Joined
·
754 Posts
I've been asked what the load rating was on the H2 rims, so I sent an Email to Hummer inquiring. They sent me back an Email stating they don't have those specs, I should check with a dealer. Called a dealer, they have no idea
. Next check is going to be Alcoa, then DOT. I'll get an answer one way or another..I hope.





Mike
 

·
Registered
Joined
·
704 Posts
They are Forged
 

·
Registered
Joined
·
3,605 Posts
so far the H2 rims have held up fine truckpulling with a 40000#+ sled in tow
 

·
Registered
Joined
·
6,995 Posts
so far the H2 rims have held up fine truckpulling with a 40000#+ sled in tow and a little extra in the HOSEPOWER dept.






tell him the whole story
 
1 - 7 of 7 Posts
Top