Diesel Place banner

1 - 20 of 149 Posts

·
Knows The 6.5
Joined
·
3,142 Posts
Not to long ago I asked TD if he wanted some "DIY" threads to help everyone out, guess what his answer was? :D
Also a recent thread came up, about making high idle "kits"
I'm willing to make them if people want to buy them, just PM me
I have a few "on order" and I'll take a pic of both an OBD1 kit and OBD2 kit once I have em both made up.

With that being said I thought to myself, how will they know how to install this?
Kennedy's instructions are good, but I know that people like pictures, so this is a how to install high idle switches..... or switch on your OBD2 trucks. (What you'll need can be found here if makin your own)

Before unplugging things and pulling things apart, you might want to disconnect your batterys.
I also want to say that I have an OBD2 truck, and it will differ some from an OBD1 truck's installation. if there is anyone around my area with an OBD1, and wants help installin a high idle switch, I'll be more then happy to hook you up with what you need, and do a free install so we can do an OBD1 dedicated high idle with pics of an OBD1 setup. PM me if interested.

Ok, lets start off with the first picture, to make removing the dash easier, I turned the key to on, and pulled the shifter down to first.


2nd pic, if you got a cup holder, you gotta move it.


As you can see in the 3rd pic, I just grab the top of my dash and gently yet firmly pulled it towards myself.


As seen in the 4th and 5th pics, you just pull the dash out enough so you can get your fingers in to remove the cargo lamp switch, as well as the headlight switch/ interior light dimmer (Not shown).

Pic 4


5th pic also shows you how the clip locks in, you gotta press down pretty firmly to get it, try wiggling as you pull.


Now take note in pic 6 of how many silver clips there are and where, this is what holds your dash in, and will make removal and reinstallation easier.


Pic 7, holes made are 1/2 using the switches I used, I picked the area of the dash on the drivers side of the steering wheel, careful using that area though, I got my switches tucked in their so nicely,


(Pic 8) with the housing side by side, I thought it was gonna interfear with the location pin and mount, but that's why careful planing and measuring more then once is done (Told ya I was a custom fabricator :D)



Picture 8 also shows the rubber "dust flap" that I used to route my wires behind the dash where the steering wheel is to keep them hidden.

Picture 9 10 and 11 show you how I ran my lines, and how I hooked the lines under the edge of the gauge cluster to keep everything behind the dash.

Pic 9


In pic 10 that switch you see is for my bumper mounted driving lights.


Pic 11


Pic 12 shows where I ran the line down behind the cup holder and airvent, into the glovebox opening.


In picture 13 there's a plastic "limiting" strap that you have to pull toward yourself while you push back on the glovebox (as if to close it) and then when it slides forward, pull it away from the glovebox.


Pic 14 on the other side of the glove box there is a stopper, just push it on it, then the glove box will come out once you lower it to almost horizontal, then gently pull towards yourself, and it'll come out.


Pic 15 is where the wire comes from behind the cupholder and airvent into the glovebox opening.


Pic 16 shows the PCM in it's stock location,


Pic 17 shows a harness that you should pull out of your way for more room, then grab the PCM and pull back on it to pull it off it's tray,


then angle it as shown in pic 18


and pull it out like shown in pic 19.


The middle connector, is the one we are after as shown in picture 20, to remove the locks you need a little flat screw driver or in my case...a pen (Gf handed it to me... it worked... why complain?)

Pic 20


and you want to remove the one without the big clip on it (as seen in pic 21, big clip is left alone)

Pic 21


The row with the lock with the big clip is row A and the other one with the flat lock is row B, (I'm takin a guess that it all looks the same for OBD1 and OBD2, if not, I'm sorry) Now here is were it gets different for the 2 OBD systems.

OBD2 you can supply 1 or 2 switched grounds to terminals B7 (1170rpm) and/or B8(1360rpm) or you can ground both and get (1600rpms)

OBD1 you supply one switched 12v power source to pin A6(1075rpm)
Going by picture 21, 1 is the far right and 12 is far left.

Pic 22 is a blury pic of the pin connector... Tried to get it... Oh well, Sorry.


Pic 23 is both pins installed, I colour coded my wires so I knew what wire went to what switch (Black is 1070rpm red is 1360rpm)


Pic 24 is with the lock put back in place


Pic 25 is of the wire routed to the PCM put back in it's stock location, to do this, there is a locator pin on the PCM and 2 clips, the pin goes into a hole on the PCM tray, and the clips slide UNDER the tray holdin the PCM in place.


These are the switch to ground wires, I dropped them down beside the steering wheel then I had to undo the screw to the mounting bracket, and replaced the screwafter moving the grounding tabs over the hole as seen in pictures 26 and 27 and that pretty much takes care of that.

Pic 26


Pic 27


Picture 28 shows the switches that I use and will use in my kits.


Now you can turn the key, flick the switch(es) and enjoy your new high idle mod :D
 

Attachments

  • Like
Reactions: Stonesway

·
Knows The 6.5
Joined
·
3,142 Posts
Discussion Starter #3

·
Registered
Joined
·
29 Posts
That is a great video and excellant pics. TY for the info. I've been makin plans to do this for mine but working on other problems with the truck.
 

·
Registered
Joined
·
2,881 Posts
good pics, people luv it when it is in pics. something about a thousand words. now lets here about the roll up the rim. couldn't help but notice timmy's cups. Ed
 

·
Registered
Joined
·
1,521 Posts
Thats a multi step up from the brick on the pedal trick .
 

·
Registered
Joined
·
1,182 Posts
Nice write up. Pics and a video, :cool:

Good job man!
 

·
Knows The 6.5
Joined
·
3,142 Posts
Discussion Starter #9
good pics, people luv it when it is in pics. something about a thousand words. now lets here about the roll up the rim. couldn't help but notice timmy's cups. Ed
I won the right to please play again :D So did the missus, you can actually see her workin on takin out the glovebox in the pic where i have the dash on my hood. Made everything 2x faster, I also didn't have to grow a third arm to take pics with :rolleyes:
 

·
She Don't Smoke!
Joined
·
4,690 Posts
Like the pics and everything, I wish I could pull my PCM out like that, i don't have much play in the wireharness. Get in Chat, I'm bored :p
 

·
Registered
Joined
·
3,964 Posts
Very nice job Justin! I'm thinking this mod will have to be tackled by me one day.

Hey, I like the way you complete the project by giving us a vid. By the way, your truck sounds great! :)
 

·
Registered
Joined
·
1,182 Posts
I won the right to please play again :D So did the missus, you can actually see her workin on takin out the glovebox in the pic where i have the dash on my hood. Made everything 2x faster, I also didn't have to grow a third arm to take pics with :rolleyes:
I noticed the missus in the pic, will she come help me do mine?
 

·
Registered
Joined
·
441 Posts
Nice job i am going to do my suburban just like yours thanks
 

·
Registered
Joined
·
266 Posts
I just did my 95 today I will post pix of the install tommorow! good job Justin
 

·
Registered
Joined
·
240 Posts
Please do post your pix Dracor85- we could use some OBDI visuals! Thanks!

Jon "OBDI Kanobe" Hobbs

I just did my 95 today I will post pix of the install tommorow! good job Justin
 

·
Registered
Joined
·
249 Posts
x2
 

·
Knows The 6.5
Joined
·
3,142 Posts
Discussion Starter #18 (Edited)
this needs to be kept as a sticky in the mods section,.i had to go looking for it today,.

nick
Man, your phone call confused the hell out of me today, I had no clue who I was talkin to for the first 10 mins :D Came up distributel on Caller ID, Then some dude talkin about white trucks and my gf and high idle :rolleyes: Lol! I was thinkin it was you, you'd be the only stranger callin my cell.

Now get your ass down here Nick, gotta decide if 20PSI is too much :p:
 

·
Knows The 6.5
Joined
·
3,142 Posts
Discussion Starter #19

·
Registered
Joined
·
363 Posts
Bump, i'm sure there are some people looking for this right about now just before winter :D
 
1 - 20 of 149 Posts
Top