LML: P0112 code - Diesel Place : Chevrolet and GMC Diesel Truck Forums
 
Home Forum Market Place Garage Tuning Library DTC Tool Register Vendors
Go Back   Diesel Place : Chevrolet and GMC Diesel Truck Forums > GM Diesel Engines > Duramax Fifth Generation: 2011-2016 (LML)
Register FAQ Forum Rules My Replies My Threads Mark Forums Read Advertise


Duramax Fifth Generation: 2011-2016 (LML) Discuss the fifth generation (2011-2016) of the 6.6L Duramax diesel engine & associated components. Engine related discussion ONLY.

DieselPlace.com is the premier Duramax Diesel Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools
Old 03-23-2017, 02:47 PM   #1 (permalink)
csholovach
Low Boost
 
Join Date: Mar 2017
Posts: 6
iTrader Score: 0 reviews

P0112 code

has anyone had a problem with code P0112 i replace the mass air flow and still poping up any help would be great!

Offline  
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 03-24-2017, 01:30 AM   #2 (permalink)
davester
Diesel Prodigy
 
Join Date: May 2015
Posts: 4,146
iTrader Score: 0 reviews

If you replaced it with a new sensor and you still get the code:

-new sensor is bad
-wiring/connector problem

__________________
2004 GMC Sierra 3500 C&C, added 4WD, 6.0L gas, Extended Cab, SLE, Transgo 4L80e-HD2 kit installed
Whee! Dually Club Member #1109
Offline   Reply With Quote Quick reply to this message
Old 03-24-2017, 10:48 AM   #3 (permalink)
Ramblinrodney
Diesel Veteran
 
Ramblinrodney's Avatar
 
Join Date: Sep 2006
Location: Midland, MI
Posts: 5,229
iTrader Score: 0 reviews

Michigan Oil Burners Member

Code P0112 sets when the voltage signal to the PCM from the Intake Air Temperature Sensor Circuit stays below .5 volts while the Coolant Temperature Voltage readings are rising and falling within an appropriate range.
Is your air filter dirty?
Faulty or corroded Intake Air Temperature Sensor wiring or connection.
Any other codes?



How to diagnose the maf trouble
Circuit/System Description

The mass air flow (MAF) sensor is integrated with the intake air temperature (IAT) sensor. The MAF sensor is an air flow meter that measures the amount of air entering the engine. The engine control module (ECM) uses the MAF sensor signal to provide the correct fuel delivery for all engine speeds and loads. A small quantity of air entering the engine indicates a deceleration or idle condition. A large quantity of air entering the engine indicates an acceleration or high load condition. The MAF/IAT sensor has the following circuits:

A MAF sensor ignition 1 voltage circuit
A MAF sensor ground circuit
A MAF sensor signal circuit
A IAT sensor signal circuit
A IAT sensor low reference circuit
The ECM applies 5 volts to the MAF sensor on the MAF sensor signal circuit. The sensor uses the voltage to produce a frequency based on the inlet airflow through the sensor bore. The frequency varies in a range depending on engine coolant temperature (ECT) of approximately 2,300 Hertz at idle to near 9,000 Hertz at maximum engine load.

When engine coolant temperatures reach 60C (140F) the ECM commands a Rich Idle mode. During Rich Idle the exhaust gas recirculation (EGR) valve is commanded ON, and a lower frequency and g/s value will be indicated on the scan tool.

Conditions for Running the DTC


DTCs P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0642, P0643, P0652, P0653, P0698, P0699, P2228, P2229 are not set.
The intake air temperature (IAT) is greater than -7C (+19.4F).
The engine coolant temperature (ECT) is less than 99C (210F).
The BARO is greater than 72 kPa.
The engine speed is greater than 500 RPM.
The exhaust gas recirculation (EGR) valve is OFF.
This DTC runs continuously within the enabling conditions.
Conditions for Setting the DTC

The ECM detects that the MAF sensor air flow ratio is not within a predetermined range of the calculated MAF air flow ratio for greater than 16 seconds.

Action Taken When the DTC Sets


DTC P0101 is a Type A DTC.
The ECM commands reduced engine power as a remedial action.
The driver information center (DIC) or indicator may display reduced engine power.
DPF regeneration is inhibited.
Conditions for Clearing the DTC

DTC P0101 is a Type A DTC.

Diagnostic Aids


A slight to moderate resistance of 10-20 ohms on the MAF sensor ignition 1 voltage circuit may cause this DTC to set.
Certain aftermarket air filters may cause this DTC to set.
Certain aftermarket air induction systems may cause this DTC to set.
Modifications the air induction system may cause this DTC to set.
A inaccurate MAF sensor, an intake air flow restriction or any unmetered air that enters the engine downstream of the MAF sensor may cause this DTC to set.
An aftermarket exhaust system may reduce engine back-pressure excessively and cause this DTC to set.
Circuit/System Verification

Special Tool

J 38522 Variable Signal Generator
Verify that DTCs P0047, P0048, P0102, P0103, P0106, P0403, or P0405 are not set.
If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle.
Ignition ON Engine OFF, observe the scan tool MAP and BARO parameters. The MAP and BARO parameters should be within 4 kPa of each other.
If greater than the specified range, replace the MAP Sensor.
Verify that restrictions do not exist in the exhaust system.
Verify that leaks do not exist in the exhaust system.
Engine operating at idle; observe the scan tool MAF Sensor parameter. The reading should be between 10-40 g/s depending on the ECT temperature.
A WOT acceleration from a stop should cause the MAF Sensor parameter on the scan tool to increase rapidly. This increase should be from 10-40 g/s at idle to greater than 400 g/s at the time of the 1-2 shift.
Operate the vehicle within the Conditions for Running the DTC to verify that the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing

Important:

You must perform the Circuit/System Verification before proceeding with the circuit/system testing.
You must perform the Repair Verification after completing the Circuit/System Testing.
Verify the integrity of the entire air induction system by inspecting for the following conditions:
A dirty or deteriorating air filter element.
A leaking, loose, or cracked PCV pipe and seal.
A loose or disconnected charge air cooler hose or pipe.
A restricted or collapsed air intake duct.
A misaligned or damaged air intake duct.
Any objects blocking the air inlet probe of the MAF/IAT sensor.
Any contamination or debris on the sensing elements in the probe of the MAF/IAT sensor.
A cracked or damaged MAF sensor housing.
Any water intrusion in the induction system.
Any snow or ice build-up at the air cleaner or MAF Sensor.
Any snow, ice build-up, or coking at the manifold absolute pressure (MAP) sensor.
An intake manifold leak.
A MAP sensor seal that is missing or damaged.
An Intake Manifold Resonator with a leaking seal, or a cracked or broken housing.
Ignition OFF, disconnect the harness connector at the MAF/IAT sensor.
Ignition OFF and scan tool disconnected for 90 seconds, test for less than 5 ohms between the MAF low reference circuit terminal 2 and ground.
If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
Ignition OFF and scan tool disconnected for 90 seconds, test for less than 5 ohms between the IAT sensor low reference circuit terminal 4 and ground.
If greater than the specified range, test the IAT sensor low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
Ignition ON, verify that a test lamp illuminates between the ignition 1 voltage circuit terminal 3 and ground.
If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal 1 and ground.
If less than the specified range, test the MAF signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
If greater than the specified range, test the MAF signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
Ignition OFF, connect the harness connector at the MAF/IAT sensor.
Engine running at a warm stabilized idle, perform the following:
8.1 Command the EGR solenoid to 0 percent with a scan tool. 8.2 Observe the Airflow Leak Equivalence Ratio parameter for 10 seconds. The value should be between 0.87:1 and 1.15:1. 8.3 Observe the Airflow Leak Equivalence Ratio parameter while slowly increasing the engine speed until reaching wide open throttle (WOT). After 10 seconds, the value should stabilize and be between 0.87:1 and 1.15:1.
If not within the specified range, test the charge air cooler system and air inlet system for leaks. Perform the Full System Air Leak Test and the Induction System Smoke Test. Refer to Charge Air Cooler Diagnosis. If no air leaks are found, test all of the MAF sensor circuits for high resistance.
Remove the Intake Manifold Tube.
Visually inspect the EGR valve and verify the valve is in the closed position.
If the EGR valve is not in the closed position, replace the EGR valve and gaskets.
Ignition OFF, disconnect the harness connector at the MAF/IAT sensor.
Ignition OFF, connect the red lead of the J 38522 to the signal circuit terminal 1 at the MAF/IAT sensor harness connector. Connect the battery voltage supply to B+. Connect the black lead to ground.
Set the J 38522 signal switch to 5 volts, the frequency to 5K, and the Duty Cycle to Normal.
Engine idling, observe the scan tool MAF Sensor parameter. The scan tool MAF Sensor parameter should be between 4.950-5.025 Hz.
If the MAF Sensor parameter is not within the specified range, replace the ECM.
If all circuits test normal, test or replace the MAF/IAT sensor.
Repair Verification


Install any components or connectors that have been removed or replaced during diagnosis.
Perform any adjustment, programming, or setup procedures that are required when a component or module is removed or replaced.
Clear the DTCs.
Turn OFF the ignition for 90 seconds.
Duplicate the Conditions for Running the DTC and use the freeze Frame/Failure Records, if applicable, in order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to the Diagnostic Trouble Code (DTC) List - Vehicle and perform the appropriate diagnostic procedure.
Perform the Diesel Particulate Filter (DPF) Service Regeneration.
__________________
07 Chevy Classic 2500HD 4x4 2LT LBZ CC/SB White
Nasta Nerf Bars, Line-x, Rancho RS9000XL Shocks, Firestone air bags, Fold-a-cover,
Good/Year Wrangler S/A 265/75/16 E
Transgo Jr. PCV Reroute kit, Trans Line Repair Kit By Dirty Hooker Diesel,
Custom Perf/Tow Tune by Kennedy
2019 Arctic Fox 27-5L 10,500 dry weight
UAW Local 699 Retired Test Technician

Last edited by Ramblinrodney; 03-24-2017 at 11:03 AM.
Offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 03-24-2017, 10:52 AM   #4 (permalink)
csholovach
Low Boost
 
Join Date: Mar 2017
Posts: 6
iTrader Score: 0 reviews

The dealer installed a remote mounted temp sensor could that have gone bad
Offline   Reply With Quote Quick reply to this message
Old 03-24-2017, 11:08 AM   #5 (permalink)
heymccall
Diesel Elite
 
heymccall's Avatar
 
Join Date: Feb 2005
Location: Butler county, PA USA
Posts: 17,715
iTrader Score: 0 reviews

Is the truck stock, right down to the factory air box and intake tubing? What year is it? How many miles?
__________________
Brian
'13 Hyundai Genesis Coupe handshaker
'14 Peterbilt 337 handshaker
Quote:
Originally Posted by GetSome8.1HD
Its not like I said I enjoyed reading Good Housekeeping while taking a candle lit bubble bath then proceeding to using a loofah with exfoliating creams all while thinking about you . Now THAT would be creepy
Member #21 of the OiO association
Offline   Reply With Quote Quick reply to this message
Old 03-24-2017, 01:49 PM   #6 (permalink)
csholovach
Low Boost
 
Join Date: Mar 2017
Posts: 6
iTrader Score: 0 reviews

The truck is a 2014 with ppei ez link and a lift pump with 5in flow pro
Offline   Reply With Quote Quick reply to this message
Old 03-24-2017, 01:50 PM   #7 (permalink)
csholovach
Low Boost
 
Join Date: Mar 2017
Posts: 6
iTrader Score: 0 reviews

Quote:
Originally Posted by csholovach View Post
The truck is a 2014 with ppei ez link and a lift pump with 5in flow pro
100000miles
Offline   Reply With Quote Quick reply to this message
Old 03-24-2017, 10:55 PM   #8 (permalink)
briano
Diesel Veteran
 
briano's Avatar
 
Join Date: Sep 2004
Location: Austin, Tx
Posts: 5,106
iTrader Score: 0 reviews

think this is a dupe to the other post from the friend..

forgets to mention he has a K&N oiled air filter. ;-)

most likely your problem if I had to guess...
__________________
14 LML 2500HD CC 4x4 - New
04.5 LLY 2500HD
- Sold.

LLY FAQ, Most Popular Tuner, Most Popular Exhaust, How to Search, Front Pipe Install,
Duramax Engine Pics, Front Pipe vs. Down Pipe Which Engine do I have?? Programmer Comparison Dual Electric Fan Install Online Manuals MBRP Powertube Install and Dyno "True" Downpipe Install

Please create a signature under User CP with year, make, and any mods. This will help us help you.
Offline   Reply With Quote Quick reply to this message
Old 03-25-2017, 08:34 AM   #9 (permalink)
csholovach
Low Boost
 
Join Date: Mar 2017
Posts: 6
iTrader Score: 0 reviews

The problem was a remote temperature sensor the dealer installed! Thanks for all your help guys!
Offline   Reply With Quote Quick reply to this message
Old 03-25-2017, 09:20 AM   #10 (permalink)
dmax3500
Diesel Ace
 
Join Date: Mar 2005
Location: chi-town
Posts: 12,726
iTrader Score: 0 reviews

remote temperature sensor,for what?

__________________
2013 2500 ltz 4x4 d/a,, fully loaded ,white crew cab
Offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Diesel Place : Chevrolet and GMC Diesel Truck Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

PLEASE READ! You must check your email inbox for the confirmation link to complete registration. Please check your spam box if you do not see the email in your inbox.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Intermittant. Code 36 ...(sighs) CJG 3500 6.5L Diesel Engine 9 11-18-2016 12:20 AM
code 57 related to vacuum pump? Skyviper 6.5L Diesel Engine 1 04-30-2016 09:59 PM
Codes 33, 44, and 68, Vin code F with 3 solenoids? EGR/Vac pump delete Please Help! Skyviper 6.5L Diesel Engine 11 04-30-2016 09:15 PM


All times are GMT -4. The time now is 11:29 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.1 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
© AutoGuide