Ally 6Spd: No forward or reverse - Diesel Place : Chevrolet and GMC Diesel Truck Forums
 
Home Forum Market Place Garage Tuning Library DTC Tool Register Vendors
Go Back   Diesel Place : Chevrolet and GMC Diesel Truck Forums > GM Transmissions > Allison Aftermarket
Register FAQ Forum Rules My Replies My Threads Mark Forums Read Advertise

Allison Aftermarket Discuss aftermarket Allison upgrades as well as repairing & maintaining them.

DieselPlace.com is the premier Duramax Diesel Forum on the internet. Registered Users do not see the above ads.
Like Tree1Likes
  • 1 Post By javejensen

Reply
 
LinkBack Thread Tools
Old 10-27-2019, 05:45 PM   #1 (permalink)
javejensen
Low Boost
 
Join Date: Oct 2019
Location: southern Utah
Posts: 6
iTrader Score: 0 reviews

No forward or reverse

Just installed new torque converter and transgo jr. Shifter will go through all the gears fine no binding. Indicator light will not come out of park and will turn on and off every few seconds or so. Truck will give a slight jolt if it’s in drive position when the light comes back on. Any help is appreciated. Thanks

__________________
2007 classic LBZ.
intake, full exhaust from manifolds to straight pipe. Dmaxstore torque converter and transgo jr.
Offline  
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 10-27-2019, 05:50 PM   #2 (permalink)
OkDually
Administrator
 
OkDually's Avatar
 
Join Date: Jul 2013
Location: N.E. Oklahoma
Posts: 14,111
iTrader Score: 0 reviews

DieselPlace.com Lifetime Premium Member

Quote:
Originally Posted by javejensen View Post
Just installed new torque converter and transgo jr. Shifter will go through all the gears fine no binding. Indicator light will not come out of park and will turn on and off every few seconds or so. Truck will give a slight jolt if it’s in drive position when the light comes back on. Any help is appreciated. Thanks
Welcome to DieselPlace
Please take a moment to tell us more about the truck( ie. Year, Make, and Model, etc..) and list any known mods done.
Also, let us know what part of the country you are located in to help the other members when giving you diagnostic or repair advice for any possible climate-related conditions.



__________________
1996 K3500 6.5L,( "F" Eng #141 cast block) 5 speed manual, crewcab, dually longbed: 208,000mi.
Diamond Eye 4" Turbo Back Exhaust w/2.5" Flo-Pro Crossover
AirDog II DF165 w/ tank sock delete - XDP
TD-Max boost controller - Kennedy Diesel
OPS extension hose - Leroy Diesel
Glow Plug Harness- PT Wiring Solutions
Glowshift Maxtow EGT,Boost, Fuel gauges
Boost & Fuel Pressure Bolts - Leroy Diesel
2/0 Battery Cable Upgrade - PT Wiring Solutions
PMD w/#9 resistor and Re-Location Kit, mounted to bumper - Leroy Diesel
GM-5 Turbocharger
4.10 gear ratio
OptiLube Winter Formula


Proud member #1039 of The 3500 Dually Club


Last edited by OkDually; 10-27-2019 at 05:50 PM.
Online   Reply With Quote Quick reply to this message
Old 10-27-2019, 05:55 PM   #3 (permalink)
javejensen
Low Boost
 
Join Date: Oct 2019
Location: southern Utah
Posts: 6
iTrader Score: 0 reviews

Truck is a 2007 classic LBZ. Truck mods are intake, full exhaust from manifolds to straight pipe. Dmaxstore torque converter and transgo jr. Located down in southern Utah
__________________
2007 classic LBZ.
intake, full exhaust from manifolds to straight pipe. Dmaxstore torque converter and transgo jr.
Offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 10-28-2019, 09:45 AM   #4 (permalink)
Rvn4me
Diesel Pro
 
Rvn4me's Avatar
 
Join Date: Jun 2016
Posts: 2,267
iTrader Score: 0 reviews

Michigan Oil Burners Member

You have missed the shift pin in the shift valve--or the wrong place—
Take the pan back off, get the shift pin back in the valve body correct. Simple fix. Good luck.
There’s lots of YouTube videos and directions on this.

Last edited by Rvn4me; 10-28-2019 at 09:47 AM.
Offline   Reply With Quote Quick reply to this message
Old 10-28-2019, 05:48 PM   #5 (permalink)
javejensen
Low Boost
 
Join Date: Oct 2019
Location: southern Utah
Posts: 6
iTrader Score: 0 reviews

The shift pin is in where it needs to be in the shifting mechanism. As far as I can tell there’s only one way it goes in. The shifter moves freely and I can still select neutral and park
__________________
2007 classic LBZ.
intake, full exhaust from manifolds to straight pipe. Dmaxstore torque converter and transgo jr.
Offline   Reply With Quote Quick reply to this message
Old 10-29-2019, 09:09 PM   #6 (permalink)
javejensen
Low Boost
 
Join Date: Oct 2019
Location: southern Utah
Posts: 6
iTrader Score: 0 reviews

Throwing codes p0852, p0843, p0877
__________________
2007 classic LBZ.
intake, full exhaust from manifolds to straight pipe. Dmaxstore torque converter and transgo jr.
Offline   Reply With Quote Quick reply to this message
Old 10-30-2019, 09:57 AM   #7 (permalink)
Rvn4me
Diesel Pro
 
Rvn4me's Avatar
 
Join Date: Jun 2016
Posts: 2,267
iTrader Score: 0 reviews

Michigan Oil Burners Member

Codes p0852, p0843, p0877
These three code are leading to your IMS Switch.
GM Part :29546972 SWITCH, Transmission Oil Pressure, SWITCH,TRANS FLUID PRESSURE(INCLUDES TEMPERATURE SENSOR) Replaced by:24293418

Your IMS could have gotten dirt, o-ring, bolts not torqued right, not plugged in correctly, etc.
You need to go over your transgo jr. installation.
https://www.dieselplace.com/forum/71...-could-do.html

P0852
Circuit/System Description

The engine control module (ECM) provides 12 volts to the park/neutral position (PNP) switch. The switch consists of 5 separate circuits, 4 of which indicate gear selector position to the transmission control module (TCM), and one that indicates park/neutral position to the ECM. When the transmission is in Park or Neutral, the switch closes and pulls the ECM voltage low, 0 volts. When the transmission is not in Park or Neutral, the ECM voltage is high, 12 volts. The ECM uses the switch in order to enable starter operation.

Conditions for Running the DTC

DTC P0851
Ignition voltage is between 11-18 volts.
The ignition is ON.
DTC P0852 is not active.
DTC P0852

Ignition voltage is between 11-18 volts.
Ignition is ON.
DTC P0851 is not active.
No GMLAN error messages.
Engine speed is more than 650 RPM.
Actual engine torque is more than 120 N.m (89 lb ft).
Accelerator pedal position is more than 6 percent.
Vehicle speed is more than 24 km/h (15 mph).
Conditions for Setting the DTC

DTC P0851

The ECM detects the Park/Neutral switch signal equals 12 volts (high) when the IMS reports a Park/Neutral range for 5 seconds.

DTC P0852

The ECM detects the Park/Neutral switch signal equals 0 volts (low) when the IMS reports a Drive range for 5 seconds and the following conditions are present:


TP is equal to or greater than 6 percent.
Engine torque is equal to or greater than 120 N.m (89 lb ft).
Vehicle speed is equal or greater than 24 km/h (15 mph).
Action Taken When the DTC Sets


DTCs P0851 and P0852 are Type C DTCs.
The ECM uses IMS range for engine start-up.
Conditions for Clearing the DIC/DTC

DTCs P0851 and P0852 are Type C DTCs.

Diagnostic Aids

It is possible for this DTC to set due to a stack-up or misalignment issue between the IMS and the P/N Switch, where no electrical fault is present. Ensure the gear shift selector cable is properly adjusted and there are no service bulletins that address this concern before replacing parts.

Circuit/System Verification

If there are any other engine or transmission related DTCs set, diagnose those DTCs first. With a scan tool observe the Park/Neutral switch parameter in the engine controls data list and move the gear shift lever from Park, to Reverse and through all the ranges and observe the parameter as you move the shift lever. The parameter should display Park/Neutral when in Park or Neutral and In-Gear when in Reverse, Drive or Drive Low. It is especially important to closely observe the Park and Neutral to Drive transitional positions while moving the shift lever and observing for possible misalignment or slack in the shifter mechanism.

Circuit/System Testing


Ignition OFF, transmission in Park or Neutral, disconnect the transmission 20-way connector.
Test for less than 1 ohm of resistance between the Park/Neutral signal circuit terminal R on the transmission side and ground.
If greater than the specified range, test the signal circuit between the connector and the IMS for an open/high resistance. If the circuit tests normal, replace the IMS.
Ignition On, verify the Park/Neutral parameter displays In-gear.
If not the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the ECM.
Install a fused jumper between the signal circuit and ground. Verify the Park/Neutral parameter displays Park/Neutral.
If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
1) ECM replacement. Refer to Control Module References for replacement, setup, and programming.
2) IMS replacement. Refer to Manual Shift Shaft, Detent Lever, and Position Switch Assembly Replacement

P0843 = Transmission Fluid Pressure Sensor/Switch "A" Circuit High
The TFP switches may stick from time to time causing a code to set.

P0877 Transmission Fluid Pressure Sensor/Switch “D” Circuit Low
Attached Images
File Type: jpeg E9620467-75C8-4116-92B1-D14BC7B548D0.jpeg (38.3 KB, 13 views)

Last edited by Rvn4me; 10-30-2019 at 10:20 AM.
Offline   Reply With Quote Quick reply to this message
Old 10-30-2019, 12:56 PM   #8 (permalink)
javejensen
Low Boost
 
Join Date: Oct 2019
Location: southern Utah
Posts: 6
iTrader Score: 0 reviews

When I removed the ims from the valve body I did not see any o rings. I assumed that they were stuck to the underside of them or something. I’ll drop the pan and check for them. If they are missing, should they be replaced with any certain kind?
__________________
2007 classic LBZ.
intake, full exhaust from manifolds to straight pipe. Dmaxstore torque converter and transgo jr.
Offline   Reply With Quote Quick reply to this message
Old 11-08-2019, 05:31 PM   #9 (permalink)
javejensen
Low Boost
 
Join Date: Oct 2019
Location: southern Utah
Posts: 6
iTrader Score: 0 reviews

So I’ve double and triple checked my valve body and all seems to be in order. The blue ims has all of its o-rings, dirt free and all plugged in correctly. It all worked fine before so I’m still led to believe I’ve done something wrong somewhere. I believe the harness was pinched a little when I put the trans mount in, but upon inspection I don’t see any damaged wires on the harness. Could this have shorted anything? Could the ims just have gone bad? I read the instructions posted above but to be honest this is my first auto trans/electrical problem and quite a newbie at this
Thanks
__________________
2007 classic LBZ.
intake, full exhaust from manifolds to straight pipe. Dmaxstore torque converter and transgo jr.
Offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Diesel Place : Chevrolet and GMC Diesel Truck Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

PLEASE READ! You must check your email inbox for the confirmation link to complete registration. Please check your spam box if you do not see the email in your inbox.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 04:06 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.1 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
© AutoGuide