It just stopped working the other day, i press the little tab and then the other button. Normally the little thing comes on in the dash but it doesnt do anything. Anyone have any ideas?

Anyone ever had this problem, i installed my six gun the other day, could i have hit or broken a wire? any ideas?

My cruise quit working one day, so I pulled into a parking lot, & shut the truck off to check the fuse. The fuse looked ok, so I put it back in & took off thinking "Oh great, looks like I'll have to take it in to the dealer". After I got up to speed again, I tried it & it worked fine. :confused: Don't know if that will work for you, but it's worth a shot.

yeah i pulled the fuse and changed it with another 10 amp fuse. Still doesnt work, guess i have to go to the $tealer...aghhhhhhhhh

Whatever ended up happening Z71? I went to use mine this afternnon and had nothing, turned cruise button off back on no difference...Tried about 10 mins later and worked fine 6 times in a row...Never shut it off, only thing i did was put it in reverse and back to drive....hmm

I think some of the temp ECM codes keep it from working, but I'm not positive. I have had mine quit working and the next key cycle they are fine.

It could be in the mulltifunction switch, too. I know that on the S-trucks, sometimes parts of them go bad for no reason.

Also make sure the brake lights aren't stuck on. I have seen that little plastic switch that works off the brake pedal slip on the threads.

I know that on my old gas half ton (2004), when i did 4 wheel drive donuts it throws a code and doesnt alow the cruise to work. Just had to clear the code and it worked.

Dont know if that helps at all.

J

My cruise has quit working half a dozen times, just shut the truck of and restart, all is ok!!

mine has stoped working also at least a dozen times. i pull over and stop the motor then restart it and everything is fine. the dealer has no idea what causes this. im not sure they even beleive me.

glad to see i am not loosing my mind.....
today i started my truck went down the highway no cruise....no light on dash nothing started it up after work cruise works fine .........
must be gremlins in the system.

Mine has done that a time or 2, but when I piddle with the brake pedal it always goes back to working.

Does the Cruise Control not work too or just the dash light?

Back to what RickDLance said, it may be your Stop Lamp Switch. This switch has several contacts.

Contacts A/B - Center High Mounted Stop Lamp
Contacts C/D - to ABS System and Cruise Control Release
Contacts E/F - Auto Trans Shift Lock Control

Contacts C/D, (normally closed contacts), gets its power from Brake Fuse 10A, (located in Fuse Block Left) flows through contacts C/D and then goes to the ECM.
All the people talking about intermittant failures, and by turning truck off, shifting to reverse, all require depressing the brake.
The next time it fails, try cycling the brakes and see if it starts to work. The brake switch may need adjustment, or one of the three contacts is starting to fail.

Mine quite working one time this summer. Cruising at 65, it just cut off and wouldn't come back on. Started working the next day. Only thing I noted is that I hit 1/4 tank of fuel about the time it quit. I always thaought it may be a built in "don't run out of fuel" warning.

Try holding the Set Button for a few seconds longer. I thought mine quit working too, but if you just press the set button quickly (like I used to do on my older truck), it wouldnt work.

...Being a little stubborn, I held the button longer and then it would work. I tried at least 2 dozen times of each method and it only work with the "press and hold" method.

Had the cruise stop working on my '05....After shutting off the key, and turning it back on again it started working....

Mine does the same as jhnz71, but only after the SixGun was installed ~40K miles ago. I always thought it was six-gun related.