Here’s info I already found:
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Hollander Wheel Number, 6300 </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Wheel Size, 17 x 8.5 </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· 8 Lug on 6.5" Bolt Pattern </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Back Spacing, 5-9/16" </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Wheel Offset, +20mm (Positive Offset) </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Hub-Hole Diameter, Aprox 4-5/8" </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· Mfg. in USA </H4>
<H4 style="MARGIN: auto 0in auto 0.5in; TEXT-INDENT: -0.25in; mso-list: l0 level1 lfo1; tab-stops: list .5in">· P/N, 9594459</H4>
<H4 style="MARGIN: auto 0in"> </H4>
<H4 style="MARGIN: auto 0in">Questions:</H4>
<H4 style="MARGIN: auto 0in">1). Are the Alloy Wheels aluminum or painted? </H4>
<H4 style="MARGIN: auto 0in">2). Are they forged or cast? </H4>
<H4 style="MARGIN: auto 0in">3). One piece or two?</H4>
<H4 style="MARGIN: auto 0in">4). What is the load rating per rim?</H4>
<H4 style="MARGIN: auto 0in"> </H4>
<H4 style="MARGIN: auto 0in">I want to up-rate my l

Go with the H2 rims and E-rated 17" tires. The rims are painted, and they fit in the wheelwell without any major mods.


I think you'll be pleased with the results.


Just my .02 cents - but you asked... http://dieselplace.com/forum/smileys/Wink.gif


Edited by: NCMax

<H4 style="MARGIN: auto 0in">1). Are the Alloy Wheels aluminum or painted? </H4>
They are painted on the front side - also available in chrome at a much higher price.
<H4 style="MARGIN: auto 0in">2). Are they forged or cast? </H4>
They are cast.
<H4 style="MARGIN: auto 0in">3). One piece or two?</H4>
One piece.
<H4 style="MARGIN: auto 0in">4). What is the load rating per rim?</H4>
The load rating is not stamped or marked on the rims. These rims are not designed far a high GVWR vehicle like the forged PYOs that come on the 2500HD and 3500 trucks, so I doubt that the weight rating is as high as the PYOs. Note that GM will not even sell a SRW 3500 with PYOs - steel only. I would not use the H2 wheels on a truck that I intended to load up to or beyond the RAWR.

I've been asked what the load rating was on the H2 rims, so I sent an Email to Hummer inquiring. They sent me back an Email stating they don't have those specs, I should check with a dealer. Called a dealer, they have no idea http://www.dieselplace.com/forum/smileys/Ermm.gif. Next check is going to be Alcoa, then DOT. I'll get an answer one way or another..I hope.





Mike

They are Forged

so far the H2 rims have held up fine truckpulling with a 40000#+ sled in tow

so far the H2 rims have held up fine truckpulling with a 40000#+ sled in tow and a little extra in the HOSEPOWER dept. http://www.dieselplace.com/forum/smileys/Big Smile.gif





tell him the whole story