|
RyanU 06-07-2005, 11:46 PM So far tranny leaked for a lil bit, i think it has stopped. I hit 48lbs of boost today in 3rd gear suckin the the filter vacumn gauge to 20% and then blew the boot on the super diesel manifold off of it...LOL Massive tire spin...I cant even hold it on the road now when in extreme mode Ill post more later partsguy662 06-07-2005, 11:48 PM Good to hear Ryan.. Glad it came together for you :beerchug: tophog 06-07-2005, 11:57 PM Better get some leather driving gloves ... Cool ... so it's "aim and shoot" now huh :) Max Power 06-07-2005, 11:58 PM Swing by and pick me up for a ride. :D RyanU 06-08-2005, 04:18 AM Better get some leather driving gloves ... Cool ... so it's "aim and shoot" now huh :) it used to break the big ole 325's lose in 1-2 2-3 pretty good but it was always regain traction. now it just breaks loose and i hafta pedal it to get traction, when i get back in it....breaks loose again. vettelovralexand 06-08-2005, 06:57 AM I don't believe you, i think i'm going to have to review a video... j/k i believe you, but i still wanna see it! Dmax Tim 06-08-2005, 07:06 AM I don't believe you, i think i'm going to have to review a video... j/k i believe you, but i still wanna see it! Live would be much better than some stupid video :eek: Go for a ride and give us a review. RyanU 06-08-2005, 01:10 PM im gonna try and make another video of a mild boosted 2wd luanch at the same place i made those other launch videos. so far, so good...im gonna hafta get some stouter clamps to hold on my SD manifold. the hose clamps just dont cut it anymore...LOL fpc 06-08-2005, 03:05 PM try a hydraulics supply house for heavy duty constant torque clamps. they're expensive, but they won't slip. partsguy662 06-08-2005, 03:16 PM so far, so good...im gonna hafta get some stouter clamps to hold on my SD manifold. the hose clamps just dont cut it anymore...LOL Have your girlfriend tighten those clamps Ryan...I think she can grip the screw driver a bit tighter ):h ecc_33 06-09-2005, 02:35 PM Massive tire spin...I cant even hold it on the road now when in extreme mode Ill post more later :funnypost thats what we like to hear now can we see it ecc_33 06-09-2005, 02:36 PM hows the smoke NONE now your in sleeper mode RyanU 06-10-2005, 03:39 AM Have your girlfriend tighten those clamps Ryan...I think she can grip the screw driver a bit tighter ):h :funnypost RyanU 06-10-2005, 03:41 AM :funnypost thats what we like to hear now can we see it well i have finally replaced the clamps on the SD manifold with some t-bolt clamps so now i can give her h*ll. exhaust is almost hooked up. BTW the ATS downpipe sucked for hookin up to the rext. I hope their second bunch of downpipes are much better. LBZ DMAX 06-10-2005, 03:43 AM Ryan, good job!!!!:ro) Now, I'll say it again; :nopics:Sorry, had to do it.:muahaha: RyanU 06-10-2005, 03:51 AM i actually made my own front pipe. i took a piece of 4" pipe and i got a 4" straight connector. i had to slice the connector in the center well over half way then make a slice in the top. so i could correct the angle that the downpipe was off. then i cut a 1" wide piece off my 4" pipe and made a slice in it. i took that slice and welded it around the connector coverin up the cut where i made the bend. then i took a piece of 3/8" thick steel and made the 4 bolt flange part by drilling out the holes and cuttin the pipe section out with a torch. welded the pipe to the flange and throw a clamp where the connector slide on the downpipe and that does it. can you believe that what i had to go through for exhaust? I had received my 4" MBRP front pipe but it wouldnt work either so im gonna send it back and get my $122 back...LOL LBZ DMAX 06-10-2005, 03:59 AM i actually made my own front pipe. i took a piece of 4" pipe and i got a 4" straight connector. i had to slice the connector in the center well over half way then make a slice in the top. so i could correct the angle that the downpipe was off. then i cut a 1" wide piece off my 4" pipe and made a slice in it. i took that slice and welded it around the connector coverin up the cut where i made the bend. then i took a piece of 3/8" thick steel and made the 4 bolt flange part by drilling out the holes and cuttin the pipe section out with a torch. welded the pipe to the flange and throw a clamp where the connector slide on the downpipe and that does it. can you believe that what i had to go through for exhaust? I had received my 4" MBRP front pipe but it wouldnt work either so im gonna send it back and get my $122 back...LOL So this would be a 'custom' exhaust? This turbo upgrade is definitely not for the faint at heart.:exactly: lly101 06-10-2005, 11:18 PM I just love it | ||