how to find out what kind of tune [Archive] - Diesel Place : Chevrolet and GMC Diesel Truck Forums

: how to find out what kind of tune


jocww
10-06-2009, 02:54 AM
How do I find out if my truck has a tune and what kind it is, if it has one at all.

DAVe3283
10-06-2009, 01:49 PM
Obviously look for a plug-in module on the engine harness. If there isn't one there, then have someone with EFILive read your ECU, they could tell you if it's stock. The dealer could do that with a Tech2, but it would most likely be expensive.

Some programs lock the ECU, so if you can't read the ECU, then it probably has a tune. I am not sure if you can flash over a locked ECU, or if you have to either get the code or buy a new one.

Hope that helps.

jocww
10-06-2009, 02:04 PM
Thanks it does.
I just cant seem to upload a bully dog tune, and I cant seem to clear dtcs and stuff.

justinp95
10-06-2009, 03:15 PM
PCMs are only like $200 on ebay to swap out.

jocww
10-06-2009, 06:01 PM
Are pcms hard to swap out? I guess I will start looking for them. Will swapping them out void any warranties not like I have any warranty left.

Dirtymax81
10-06-2009, 06:17 PM
they are easy to swap out

EFI Support
10-06-2009, 06:46 PM
Even if there is a custom tune in the ECM and it's been locked you should still be able to read and clear codes. Your issue suggests a communication problem that won't be fixed by replacing the ECM. First point of call would be to check the cig fuse.

Cheers
Cindy

jocww
10-06-2009, 07:50 PM
cig fuse? Is this under the hood or under the dash? cig short for cig lighter? If its the cigar one under the hood that is 15amp the fuse is good.

Dirtymax81
10-06-2009, 09:03 PM
if the cig fuse was blown a programmer wouldnt even power up

greif03lb7
10-06-2009, 09:06 PM
my friends 04 6.0 gasser did the same thing it was just a fuse also.

jocww
10-06-2009, 10:18 PM
the programmr turns on but it wont load. Is the cig fuse the cigar fuse under the hood?

justinp95
10-06-2009, 11:03 PM
If it turns on the cig fuse is fine. You can try to get the dealer to flash the PCM back to stock but if it doesnt work, get a new PCM.

jocww
10-07-2009, 01:38 AM
Ok thanks Justin, on a side not are you Justin as in Jennas husband?

justinp95
10-07-2009, 10:19 AM
Negative lol.

jocww
10-07-2009, 03:07 PM
Ok I saw black bear tune and was like I wonder haha. Do I have to go to the stealership to get a reflash or can just about anyone do that.

justinp95
10-07-2009, 05:24 PM
Dealer, i think it was about $100 when i tried to do it.

ZebBeard
10-08-2009, 07:58 AM
Some independent shops can do it. I'm just getting into that. I haven't done one yet but I have the capability.

jocww
10-08-2009, 01:04 PM
You live somewhere close to me Zeb lol.

jocww
10-15-2009, 08:20 PM
Does anyone know if my subs and or amp would have fried my ecu/pcm?

ZebBeard
10-26-2009, 08:36 PM
You live somewhere close to me Zeb lol.

No, sorry I didn't see this reply until now. I'm in South Arkansas. I'm coming to LA for thanksgiving, but it's too much crap to bring on the plane.

jocww
10-27-2009, 01:30 AM
shucks, still have this problem of course I havent messed with it in a few weeks.

jocww
01-29-2010, 02:07 PM
If I have a p0380 code the one that says my glow plugs need work. Will this cause the programmer not to work?