|
: heatsink newhere bt internet? dat1truk 09-20-2009, 04:02 PM Im havn trbl finding pmd heatsinks newhere but d internet... I kn0 they can ordr heatsinks at radio shack bt wen i went t0 ask the askd me wat knd 0f pr0ces0r i needed it 4 and i was l0st... d0 they sell heatsinks big enuf 4 a pmd 4 procesors? mrsemi05 09-20-2009, 04:27 PM any computer store should have them and if it mesures like 3inx4in it should work but bigger the better dat1truk 09-20-2009, 05:03 PM s0 h0w much am i l00kin t0 spend 0n a 5x4 0r s0 4320Diesel 09-20-2009, 05:23 PM no offence but it would make your posts easier to read and comprehend if you typed words completly and without numbers in them RCpullerdude 09-20-2009, 05:25 PM no offence but it would make your posts easier to read and comprehend if you typed words completly and without numbers in them I agree. It's rather annoying too. mtjasper 09-20-2009, 05:27 PM no offence but it would make your posts easier to read and comprehend if you typed words completly and without numbers in them I agree. It's rather annoying too. same here bud TedReminder 09-20-2009, 06:01 PM Best bet is ebay. Just search heat sink. Thousands to pick from. Ted BigBlueChevy 09-20-2009, 06:28 PM That and you can always check pmdcable.com. They have a heatsink/extension harness combo for pretty cheap if your a fabricator. And don't use that "internet language" here. This isn't some import forum. Its a respected comunity for diesels. Don't trash it. dat1truk 09-20-2009, 07:20 PM [QUOTE=mtjasper;3479581]same here bud[/QU Sorry i didnt realize i was going to recieve hate mail im getting on the site with my fone because i dont have a computer at the dorms here... Also the point of this post was to find a heat sink some place other than the internet... I have a great respect for this site its the only reason we still have that 6.5L lol 4320Diesel 09-20-2009, 07:34 PM cant you type it normally on a cell phone? JMJNet 09-20-2009, 07:50 PM Most of the CPU heatsink is good but usually don't have base thick enough to be fasten with a bolt to the bumper. There are some that can but you have to look. If you have an industrial metal supply there, they probably have it also. Check with someone local there and ask for that. dat1truk 09-20-2009, 07:57 PM K thanks for the ideas guys i will look around mtjasper 09-20-2009, 07:59 PM that wanst hate mail by any means, just a suggestion dat1truk 09-20-2009, 08:04 PM Lol ok and yal r rite i shud write most of my words out dat1truk 09-27-2009, 11:16 PM Would a socket 775 cpu heat sink work efficiently on a pmd/fsd matuva 09-27-2009, 11:48 PM I think a CPU heat sink would be to small, especially concerning where it will be in contact with the PMD. The whole surface of PMD base must be in contact with the heat sink to perform good heat transfer dat1truk 09-27-2009, 11:53 PM Did u look up d socket 775 heatsink its a monster and its about 30 buks at radio shack i thnk it wud nd triming to fit n d bumber kena 09-28-2009, 06:03 AM Just stroll through a junk yard and find yourself a power amp. They have sizeable heatsinks. You will want a big one. PMD's get really hot. TedReminder 09-28-2009, 06:44 AM http://cgi.ebay.com/SIX-6-CLEAN-HEATSINK-ALUMINUM-EXTRUSION-LARGE-BLACK_W0QQitemZ220483848720QQcmdZViewItemQQptZLH_D efaultDomain_0?hash=item3355dc8a10&_trksid=p4999.c0.m14 JMJNet 09-28-2009, 09:51 AM dat1, you can go to my garage to see pic of my heatsink. I found that at the bay. Need something similar if it does not have the leg it is fine but has to be bigger than the PMD. I am not sure how the RS heatsink look like, it may be fine. Something with 5 to 6 inches long and 3 to 5 inches wide and about 1 inch fin height. | ||