|
RUNNINHORN 05-11-2005, 10:19 AM Currently setting my truck back to stock, took both fuses out, plugged it in, and now it says "Unlocking PCM, Dont Disturb, Dont Start Engine." And it has been displaying that for about 10 minutes now--is it supposed to take this long or longer? McRat 05-11-2005, 11:24 AM Make sure the engine switch is in the full ON position. I've had the Bdog do that before. Twice. And other crappy behavior. By trying it a few times, it ended up working. Scary. When it actually goes to tune your truck, it will first save your stock tune. This takes about 5 minutes, and has a counter that counts in HEX up to about 400. Next it will ask you what tune you want, then it will take 2 minutes to upload the performance tune. Returning it to stock also takes 2 minutes. RUNNINHORN 05-11-2005, 12:18 PM DOH! Im an idiot. I turned the key only one click, i sat there for 30 mins thinking this takes forever. then i turned it one more click and everything on the dash lit up, and then it took all of 2 mins........thanks rat.... socal LLy 05-11-2005, 12:20 PM theres four fuses you need to pull not two,when you first posted about the bully dog I asked you if you wanted instructions.I posted pics if you look in the pics you can see the fuses thet need to be pulled before you begin Currently setting my truck back to stock, took both fuses out, plugged it in, and now it says "Unlocking PCM, Dont Disturb, Dont Start Engine." And it has been displaying that for about 10 minutes now--is it supposed to take this long or longer? RUNNINHORN 05-11-2005, 12:48 PM damn, i just pulled 2, hope i didnt screw up anything...... got a better pic? or a clearer pic? BullydogPowered 05-11-2005, 01:00 PM the longest programming is when going from a tune to stock and then from stock to a tune. seems like you found the problem though. socal LLy 05-11-2005, 01:05 PM Thats as good as it gets if you click on the photo it will get bigger you can see the fuses circled clearlydamn, i just pulled 2, hope i didnt screw up anything...... got a better pic? or a clearer pic? RUNNINHORN 05-11-2005, 01:06 PM i pulled the bottom two on the far right bottom. What one's did i miss? socal LLy 05-11-2005, 01:47 PM If this don't work I cant help you:) RUNNINHORN 05-11-2005, 11:40 PM thanks, i didnt pull pic fuse 1 or pic fuse 2, how do i know if i fried something? Wolford 05-11-2005, 11:54 PM You didnt fry anything. Dont worry about it. It is more of a power issue with the tuner, they want to make sure that the full batt. power is going to reading the tunes and not to the fuel pump radio etc. RUNNINHORN 05-12-2005, 12:07 AM i just re-installed the power pup, on stage 3, lets see if it acts any different...... socal LLy 05-12-2005, 01:35 AM was it acting funny(the truck that is)or are you still getting some kind of errori just re-installed the power pup, on stage 3, lets see if it acts any different...... RUNNINHORN 05-12-2005, 01:36 AM all systems are a go, its doing fine :D jetboatjockey 05-12-2005, 08:55 AM bully dog installed mine at the factory first time, and they did not pull any fuses. lly 05 chev/ socal LLy 05-12-2005, 02:11 PM did you get the power pup or there plug in box that is installed under the hoodbully dog installed mine at the factory first time, and they did not pull any fuses. lly 05 chev/ cid` 05-12-2005, 02:26 PM I've never HAD to pull fuses, always uploaded fine.. socal LLy 05-12-2005, 08:18 PM you rebel:ro)I am the type that follows distructions I've never HAD to pull fuses, always uploaded fine.. jetboatjockey 05-12-2005, 09:01 PM power pup, for the speed limiter, edge juice and attitude. | ||