I got a new keyless remote from ebay. How do i reprogram it to my truck?

what no instructions? theres a part in do-it yourself section that might help

I don't know what year and model your truck is, but this is what came with my remote on ebay.

i have a 2003 dmax 2500

put it in your signature

Important

All transmitters which are to be recognized by the PDM must be programmed in a single programming sequence. When using this program method, all previously programmed transmitters will be erased upon the receipt of the programming signal from the first transmitter.

The order in which the transmitters are programmed will determine its numbering position within the PDM memory. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. The number stamped on the transmitter case is for reference only; #2 can be programmed as #1, or vice versa. Additional unnumbered transmitters are also available.



<LI type=1>Close all the vehicle doors. <LI type=1>Insert the ignition key into the ignition lock cylinder. <LI type=1>Press and hold the door unlock switch. <LI type=1>While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. <LI type=1>Release the door unlock switch. The doors will lock and unlock to confirm the program mode. <LI type=1>Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter. <LI type=1>Repeat the previous step to program up to 4 transmitters. <LI type=1>Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter programming mode.
Operate the transmitter functions in order to verify correct system operation.

Why is step 1 blank

Important

All transmitters which are to be recognized by the PDM must be programmed in a single programming sequence. When using this program method, all previously programmed transmitters will be erased upon the receipt of the programming signal from the first transmitter.

The order in which the transmitters are programmed will determine its numbering position within the PDM memory. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. The number stamped on the transmitter case is for reference only; #2 can be programmed as #1, or vice versa. Additional unnumbered transmitters are also available.




Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to 4 transmitters.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter programming mode.
Operate the transmitter functions in order to verify correct system operation.

Never mind I see it changed when I clicked quote

anybody know if these are the same to programm the fob for an 03 cadi CTS ??

and thanks this worked great on my 04 gmc i just picked up...

dave

Need a Tech II for the CTS

How about a 2001 Olds Silouette?

Olds silouette. Dont worry about number 1 missing, for whatever reason it bumped everything down and added a 13 to it.

Transmitter Programming

Important: All transmitters which are to be recognized by the remote control door lock transmitter (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.

<LI type=1>Remove the ignition key from the ignition lock cylinder. <LI type=1>Remove the BCM PRGRM fuse from the fuse block. Refer to Electrical Center Identification Views (http://service.gm.com/servlets/CellHandler?CellId=62019&RefDoc=690268&evc=sm) in Wiring Systems. <LI type=1>Close all of the doors. <LI type=1>Insert the ignition key into the ignition lock cylinder. <LI type=1>Within 1 second, perform the following actions: Turn the key to ACC, then to OFF, then to ACC. <LI type=1>If you only do the 1st step, then the BCM will give feedback indicating the actions so far are incorrect. To program the transmitter, you must do step 5 instead. If step 5 is done correctly, then the BCM may flash trouble codes. In this case, you would refer to Diagnostic System Check - Body Control System (http://service.gm.com/servlets/CellHandler?CellId=8875&RefDoc=690268&evc=sm) in Body Control System. <LI type=1>Open and then close any vehicle door. The BCM will chime in order to confirm that the programming mode has been entered. <LI type=1>Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for approximately 14 seconds. Important: After approximately 3-5 seconds the BCM will chime once to confirm that the programming has been completed for that transmitter.

<LI type=1>Repeat the previous step in order to program each additional transmitter. <LI type=1>Remove the ignition key from the ignition lock cylinder. <LI type=1>Install the BCM PRGRM fuse into the fuse block.
Operate the functions of each transmitter in order to verify correct system operation.

Need a Tech II for the CTS

hmm so does this mean it has to be done by the dealer ??

why ??

thanks
dave

Or anyone with a Tech II

Why? Because thats the way GM wanted it