Just got the book, the box, and the programmer out, but where do i plug it into?:help: How do i program it exactly? it doesnt say in the books i have.......

Under the drivers side dash just under the steering wheel if it a power pup




2004 LB7
Bully Dog Power Pup (95hptune)
Bully Dog Stainless 4" exhaust
Bully Dog Shift Enhancer
Airrade Intake
Fab Tech 6" lift
315 BFG's<!-- / message --><!-- attachments -->
<FIELDSET class=fieldset><LEGEND>Attached Thumbnails</LEGEND>http://dieselplace.com/forum/attachment.php?attachmentid=3533&stc=1&thumb=1 (http://dieselplace.com/forum/attachment.php?attachmentid=3533)
</FIELDSET>

ok thanks. and how do i program it/reset it? Something about turning the key to the ACC position, right?

The Pup should guide you through it with on screen instructions.

The Pup should guide you through it with on screen instructions.
10-4 thanks, going out to the truck now.......

Oh also remove the required fuses on an 01-03 there all inside I think, and on 04 they are outside, plug the programmer in and the instructions are shown on the unit. May have to turn key before programmer turns on but usualy I think it tells you to turn on the key when you plug it in


2004 LB7
Bully Dog Power Pup (95hptune)
Bully Dog Stainless 4" exhaust
Bully Dog Shift Enhancer
Airrade Intake
Fab Tech 6" lift
315 BFG's<!-- / message --><!-- attachments -->


<FIELDSET class=fieldset><LEGEND>Attached Thumbnails</LEGEND>http://dieselplace.com/forum/attachment.php?attachmentid=3533&stc=1&thumb=1 (http://dieselplace.com/forum/attachment.php?attachmentid=3533)</FIELDSET>

RTFM :D You will need to read the manual because there are certain fuses you have to pull etc. If you don't read the manual you can have problems.

RTFM :D You will need to read the manual because there are certain fuses you have to pull etc. If you don't read the manual you can have problems.
dont have a manual:o:

if you still need help I have one and can tell you what to do

FTR
For those that may forget to pull a fuse, I never pull a fuse when I install a Quad, Bully Dog or Edge Box. No problems yet.

FTR
For those that may forget to pull a fuse, I never pull a fuse when I install a Quad, Bully Dog or Edge Box. No problems yet.
what color is your truck? was running on 80 thru forney yesterday, going thru there from time to time, wondering what color your truck was tobe sure to give you a smoke signal "hello" if i ever saw you:D

If you have Onstar you'd better pull the fuses, and if you need a copy of the instructions I can scan them to your Email. Jim.

If you have Onstar you'd better pull the fuses, and if you need a copy of the instructions I can scan them to your Email. Jim.
i do have onstar. Which fuses do i pull? If it isnt too much trouble, please scan and email em to me, id really appreciate it......thanks

zx-10r@comcast.net

No prpblem. I'm just leaving for mothers day dinner, I'll do as soon as I get back.

FTR
For those that may forget to pull a fuse, I never pull a fuse when I install a Quad, Bully Dog or Edge Box. No problems yet.

Ditto on my '05 with Predator. Got tired of pulling 4 fuses every time. I suspect they tell you to do that to avoid power spikes or demand situations that might interupt or corrupt the programming, but probably pretty safe without pulling the fuses. Worst case, the instructions seemed to indicate that if Onstar was still enabled (no fuse pulled) you might interupt the programming and it would have to start over...I also assume that if you corrupted a tune/program, you should always be able to restore the default programming and restart again...

Shrug.