GSXR600
02-20-2009, 11:50 AM
i would say ZEP 45 NC if anyone knows of one better... tell me cause i cant find one better than this stuff melts rust and corrosion off bolts and nuts better than anything i have ever tried
|
ottomatic 02-20-2009, 06:30 PM Kroil mac2881994 02-20-2009, 07:13 PM I have always used kroil or pb blaster. Both are really good. 08DMAXMIKE 02-20-2009, 07:50 PM If you can find a BG additive rep hit him / her up for there penetrating oil ... I watched a rep at the dealership I worked at spray a small amount on a table and stand a bolt up in it with the head up..... that stuff crawled up the bolt very good stuff....it is a bit costly but worth it in the really bad situations... but for everyday stuff I use PB blaster after a quick spray with brake clean (let it dry first) heymccall 02-20-2009, 08:05 PM I haven't found anything better than the Kimball-Midwest Torq "CB". But it is not a permanent lubricant. It will allow removal of seriously rusted nuts, though. jtaylor11 02-20-2009, 08:27 PM X3 on PB blast. Hotwater 02-20-2009, 08:35 PM Kroil BoiseRob 02-20-2009, 08:44 PM I prefer Schaeffer's Penetro 90... ktmrfs 02-20-2009, 11:31 PM Kroil x3 on Kroil. stuff is amazing RFDEV 02-21-2009, 09:12 AM x3 on Kroil. stuff is amazing same here ... best one I've found 6speedduramax 02-21-2009, 10:10 AM What about KY? It makes penetration easier.:gr_grin: I usually just use PB. Haven't found anything better around here. 98xtc 02-21-2009, 12:58 PM I haven't tried some of the ones I see listed but I would say Castle Thrust is the best stuff I have used. derrick7mm 02-21-2009, 01:23 PM Kroil, Kroil and more Kroil:D DURAtotheMAX 02-21-2009, 01:52 PM PB Blaster knuckledrager 02-21-2009, 05:17 PM my vote is for mouse milk. p_bol 02-21-2009, 07:46 PM Another vote for PB Blaster! My uncle use to maintain Caterpillar equipment and swore by this stuff. :beerchug: GSXR600 02-21-2009, 07:51 PM ive seen PB never used it .. once i did i think and kroil... never heard of it a bear 02-21-2009, 10:19 PM Kroil kawginn77 02-22-2009, 08:47 PM BG Produsts In-Force!!!! phazar 02-22-2009, 08:51 PM ky, just kidding, release all ericw13 02-23-2009, 10:26 AM i use PB blaster. the ZEP45 is not a penetrate it is strictly a lubricant. i us PB blaster to penetrate and Zep45 to lubricate. ZEP45 works great on my .45 cal also:D TrailerproPop 02-23-2009, 11:06 AM I heard of a test where they tested 30 different penetrating products. Coca-Cola worked better than 22 of them! Not sure if that's true. :D 2002DURAMAX 02-23-2009, 11:34 AM Kroil or PB Blaster. Two Goldens 02-23-2009, 12:06 PM :eek: jtaylor11 02-23-2009, 02:12 PM I heard of a test where they tested 30 different penetrating products. Coca-Cola worked better than 22 of them! Not sure if that's true. :D Coca-Cola has about as many uses as Duck Tape. foreman00081 02-23-2009, 03:31 PM another one for PB Blaster! ZL-1 02-23-2009, 04:53 PM I use Kroil and PB Blaster. Both are good...Coke and rum is also good...:D Makes you feel good about rusty nuts... GSXR600 02-23-2009, 09:42 PM i use PB blaster. the ZEP45 is not a penetrate it is strictly a lubricant. i us PB blaster to penetrate and Zep45 to lubricate. ZEP45 works great on my .45 cal also:D i dont know what your talking about it says penitraiting luricant with PFTE right on the can gregs04.5 02-23-2009, 10:04 PM Kroil all the way. wkndwaryrs 02-24-2009, 01:09 AM Rust Buster Which comes in a Zoom Spout & Knocker Loose which is an aerosol tinypeckerwood 02-24-2009, 01:53 AM I like panther piss(PB blater) Or if all else fail a friggin' torch! I really like the "Ohio Blue tip" No rust too tough! My buddy "VICTOR" can get through anything. SixPak 02-24-2009, 11:18 PM Kroil, Kroil and more Kroil:D Yep, KROIL it is! It's the best. Cougar GT-E 02-25-2009, 11:15 AM I like the GM product "Heat Pipe Lubricant". jb 08DMAXMIKE 02-26-2009, 06:27 AM Wax work really well also.... heat the bolt / nut with a torch and apply wax to it...the wax will pull to the threads and pushes to rust out of the threads....works good on broken bolts as well crawlerhauler03 02-26-2009, 06:42 AM im always workin on rusty stuff at home and work....PB seems to be the best Vin63 02-26-2009, 12:02 PM I would have to go with Kroil to remove or loosen heavily corroded/rusty fasteners, but to prevent that kind of corrosion, I would go with Gibbs Brand penetrating oil. tazman7 02-27-2009, 10:33 PM Mystic metal mover.. hands down. maxdout1 02-28-2009, 08:38 AM Got to be PB Blaster oliver 66 03-01-2009, 09:31 AM gibbs or sp3 it works the best for alot of farmers and truckers in our area it is good stuff. NICHOLS LANDSCA 03-10-2009, 02:55 PM I've had good luck with Yield but it's hard to find. Just bought a gallon of PB about a month ago. | ||